Garmin is a very well-known watch brand in the market. Its watches are known to have a long battery life but after so many charging and discharging cycles, the batteries of even these watches can also lose their capacity to hold a charge. In such scenarios, knowing the process of battery replacement can save you some bucks. In this blog, we’ll provide you with a step-by-step guide to Garmin vivoactive 3 battery replacement and Garmin vivoactive 4 battery replacement . Not only this, but you’ll also find amazing information about Garmin vivoactive 3 battery life in this blog.

How to Do Garmin Vivoactive 3 Battery Replacement?

Garmin vivoactive 3 battery replacement 
Image from Garmin.com

Batteries become tired and lose their capacity to store a charge after several charging and discharging cycles. Manufacturing flaws and poor storage might potentially cause your watch battery to lose efficiency. This simple guide will help you through the steps of changing your battery, regardless of the cause of its failure.

This process will resolve any present issues with your battery. We also urge that you learn about proper charging and storage procedures in order to get the most life out of your battery. Some of the fundamental steps to Garmin vivoactive 3 battery replacement are as follows:

Step 1: Grasp the metal screwdriver, fitted with a T5 Torx bit, in your dominant hand.

Step 2: You should use your free hand to grasp the rubber screwdriver that has a Hex T6 Torx bit attached to it.

Step 3: With your non-dominant hand, hold the rubber screwdriver in place, then use your dominant hand to unscrew the pin (anticlockwise).

Step 4: You can put the metal screwdriver back into the hole you just cleaned out after taking out the 1mm screw.

Step 5: The pin in the strap can be popped out with a gentle push. It will start sticking out the other end.

Step 6: To remove the protruding pin, simply grip it with your fingers and wiggle it loose. You can now detach the strap from the gadget.

Step 7: To remove the glue, heat the screen with an iOpener.

Step 8: About a minute after it has been used, the iOpener can be discarded.

Step 9: Learn more about the iOpener and how to use it by reading the iOpener manual.

Step 10: Carefully pry up one side of the screen by inserting the blue plastic opening tool between the screen and the plastic case of the watch.

Step 11: Once one side is loose, insert the blue pick between the screen and the watch unit on that side.

Step 12: In order to separate the screen from the adhesive on all four sides, you need just make a single pass around the outside.

Step 13: Open the glass by prying it up on one side using the blue plastic tool. To make room for your fingernail, raise it up.

Step 14: Repeat on the other side of the gadget until you can hold it securely in one hand.

Step 15: Get a firm hold of the screen on two of its sides.

Step 16: Carefully remove the display from the housing. You need to take it apart carefully so that you don’t break the connection to the motherboard.

Step 17: With the use of a plastic opening tool, gently raise the orange tab to detach the screen from the motherboard.

Step 18: After you’ve done this, you should be able to detach the display from the rest of the gadget.

Step 19: Just keep following the instructions until you get to the part where you take the battery out.

Step 20: To begin, pull the tab from the battery connector.

Step 21: Gently pry out the battery using a plastic opening tool as illustrated.

Step 22: If you remove the battery from its casing and turn it, you can see the tab that holds it in place.

Step 23: Use your fingernail to carefully lift the tab that’s been attached.

Also Read: How Does Solar Watch Work?

What is the Garmin Vivoactive 3 Battery Life?

JAN23Garmin vivoactive 3 battery replacement  According to Garmin, the Vivoactive 3 can go seven days without charging in smartwatch mode, thirteen hours in GPS mode, and five hours in GPS Plus audio mode. However, typical usable battery life is rather shorter. The watch needs to be charged about every four days. You can go around eight days without charging your watch, if you turn off Bluetooth most of the time, reduce the screen’s brightness to its minimum setting, and utilize GPS tracking once every two days for an hour.

There are better options out there, but for the vast majority of users, this one will suffice. Assuming you begin the Paris Marathon with about 80% charge, you will finish the marathon with plenty of juice left (with GPS but no music). With this, you should have understood Garmin vivoactive 3 battery life.

Also See: How Do You Charge Your Dead Eco-Drive Watch?

How to Perform Garmin Vivoactive 4 Battery Replacement? How to Fix Garmin Vivoactive 4 Battery Draining Too Fast?

According to Garmin’s official site, their outdoor watches use a rechargeable lithium-ion battery and that is not replaceable. So, it’s not possible for you to perform Garmin vivoactive 4 battery replacement. Although there isn’t a way to replace the battery yourself, you can try these fixes if your Gramin Vivoactive 4 battery is draining too fast-

Method 1: To Shorten the Display’s Timeout

The length of your battery life can be directly attributed to this. As a result, we advise you to set the screen timeout as short as possible. The steps, in case you’re wondering, are as follows:

  • Pressing and holding the B key is the first step.
  • The next step is to go to the Settings menu.
  • Get on the system right away.
  • Select Timeout by pressing the backlight button. In any case, that’s all there is to it. Turn it all the way down now.

Method 2: Lower the Screen’s Contrast

Several customers have mentioned that lowering the screen’s brightness helped them with their battery life. To that end, here are some suggestions for dimming your display:

  • Put the B button on hold first.
  • Next, click the Settings menu.
  • Get on the system right away.
  • Simply adjust the brightness by tapping the backlight and then selecting the appropriate option from the drop-down menu.

Method 3: Put Bluetooth to Sleep

Yeah! It may seem counterintuitive, but you need to turn off Bluetooth while you’re not making use of wireless connections. By doing so, you can get an extra five percent of battery life out of your Garmin Vivoactive 4 watch. Here are the necessary procedures:

  • To begin, press and hold the A button to bring up the options screen.
  • If you want to disable Bluetooth, simply press its button again.

Method 4: Using Activity Monitors

In most cases, we turned on every activity-tracking function without thinking about how it might drain the battery of our smartwatches. Here are the necessary procedures:

  • Put the B button on hold first.
  • Next, click the Settings menu.
  • Follow that by checking your activity log.
  • The last step is to make a choice from the available options, which include Status, Move Alert, Goal Alerts, Auto Activity Start, Intensity Minutes, etc.

Method 5: Restrict Excessive Smartphone Alerts

If we’re going to spend money on a smartwatch, we might as well use it. So that’s why it has an impact on our battery life occasionally. Therefore, it is important to reduce the number of alerts sent to your phone that aren’t necessary. The following are the necessary procedures:

  • To choose which Garmin Connect app alerts appear on your iOS device, navigate to the Notifications section of your device’s settings.
  • To use Android: To activate Smart Notification in the Garmin Connect app, tap Settings.

Method 6: Engage the Automatic Pulse

Use the Oximeter Readings sensor only when absolutely necessary because it drains the battery very quickly. Turning this on permanently is needless. Here are the necessary procedures:

  • Start by pressing and holding the B button until the Settings menu appears.
  • Now, select Wrist Heart Rate and then Pulse Ox.
  • Then, choose a tracking method from the menu that appears: Daily, overnight, and during the night.

Method 7: Make Sure Your Battery Is Charged

Your battery could die or get damaged at any time. This means you need to give your watch a full charge before checking the battery life. If, after regular use, the battery doesn’t last for at least half a day, you should visit the local service center to have it replaced.

With this, we have come to the end of this article. After going through the blog, you should have learned all the steps of Garmin vivoactive 3 battery replacement  and life, Garmin vivoactive 4 battery replacement. Now, Garmin watch battery replacement has become hassle-free for you.

Recommended: What is Monocrystalline Solar Panel?

Share.
mm

Olivia is committed to green energy and works to help ensure our planet's long-term habitability. She takes part in environmental conservation by recycling and avoiding single-use plastic.

Leave A Reply